Sparkfun Products In Pakistan

Sparkfun Products In Pakistan

We deals variety of Sparkfun products projects, kits and parts. It manufactures and sells microcontroller development boards and breakout boards. All products are exclusively available..
sparkfun%2Bbanner.jpg
10264-01.jpg

Flex Sensor 2.2 in pakistan

Description:
A simple flex sensor 2.2" in length. As the sensor is flexed, the resistance across the sensor increases. Patented technology by Spectra Symbol - they claim these sensors were used in the originalNintendo Power Glove. I love the Nintendo Power Glove. It’s so bad!The resistance of the flex sensor changes when the metal pads are on the outside of the bend (text on inside of bend).
Connector is 0.1" spaced and bread board friendly. Check datasheet for full specifications.
08606-03-L.jpg

Flex Sensor 4.5" in pakistan

Description:
A simple flex sensor 4.5" in length. As the sensor is flexed, the resistance across the sensor increases. Patented technology by Spectra Symbol - they claim these sensors were used in the originalNintendo Power Glove. I love the Nintendo Power Glove. It’s so bad!
The resistance of the flex sensor changes when the metal pads are on the outside of the bend (text on inside of bend).
Connector is 0.1" spaced and bread board friendly. Check datasheet for full specifications.

Force Sensitive Resistor-Square In Pakistan

09376-1.jpg
Description:
This is a force sensitive resistor with a square, 1.75x1.5", sensing area. This FSR will vary its resistance depending on how much pressure is being applied to the sensing area. The harder the force, the lower the resistance. When no pressure is being applied to the FSR its resistance will be larger than 1MΩ. This FSR can sense applied force anywhere in the range of 100g-10kg.
Two pins extend from the bottom of the sensor with 0.1" pitch making it bread board friendly. There is a peel-and-stick rubber backing on the other side of the sensing area to mount the FSR.
These sensors are simple to set up and great for sensing pressure, but they aren’t incredibly accurate. Use them to sense if it’s being squeezed, but you may not want to use it as a scale.

LinkSprite JPEG Color Camera

TTL Interface - Infrared In Pakistan

11610-05d.jpg

Description:
Are you a super spy trying to spot ninja assassins in the dark? Or maybe you’re just trying to figure out who’s been sneaking to the kitchen at night and eating your snacks… Either way, an infrared camera is the way to go! LinkSprite’s latest serial port camera module can capture high resolution pictures and transport them over TTL serial, making it ideal for embedded applications. And it can do it in the dark, thanks to infrared LEDs. The infrared feature even has a built-in light sensor, so as soon as the ambient light gets low enough, it will automatically turn on the infrared LEDs for night vision!
Dimensions: 45.6x30x28mm
Features:
  • VGA/QVGA/160*120 resolution
  • Support capture JPEG from serial port
  • Default baud rate of serial port is 38400
  • DC 3.3V or 5V power supply
  • Current consumption: 80-100mA
  • The pin near C03 is AV output pin, which is an analog output pin

FLiR Dev Kit In Pakistan:

Description:
The FLiR Dev Kit includes a breakout as well as a Lepton® longwave infrared (LWIR) imager. With this kit you will be able to be able to bring FLiR’s thermal imaging reliability and power to your Arduino, Raspberry Pi, or any ARM based development tool all in an easy to access breadboard friendly package. All you need to do to get this kit set up, simply attach the Lepton® imager module into the provided breakout, connect the headers, and you will be seeing in full darkness in no time!
13233-01.jpg
The Lepton® LWIR module included in each FLiR Dev Kit packs a resolution of 80 × 60 pixels into a camera body that is smaller than a dime and captures infrared radiation input in its nominal response wavelength band (from 8 to 14 microns) and outputs a uniform thermal image. Meanwhile, each breakout board in these kits provides the socket for the Lepton®, power supply’s, 25Mhz Crystal Oscillator, 100 mil header for use in a breadboard or wiring to any host system. A few things to consider about this kit: the breakout board will accept a 3-5V input and regulate it to what the Lepton® wants, to read an image from the lepton module all you need is an SPI port, and to configure the camera settings you also need an I2C port, although this is not required.
Note: This kit comes in two separate parts and will need to be assembled once received. The Lepton® module is extremely sensitive to electrostatic discharge (ESD). When inserting it into the breakout board be sure to use proper personal grounding, such as a grounding wrist strap, to prevent damage the module.

Magician Chassis In Pakistan

12866-01.jpg
Description:
The Magician Chassis is our latest robot platform from Dagu. It features two gearmotors with 65mm wheels and a rear caster. The chassis plates are cut from acrylic with a wide variety of mounting holes for sensors, controllers, power, etc. Simply bolt the two pre-cut platforms together, attach the motors and caster and add your favorite robotics controller. This kit includes all of the parts needed to assemble the chassis as well as a 4xAA battery holder with barrel jack termination.
This new version comes with new hardware that matches what the instructions actually say is in the kit. No more confusing mix-ups or inconsistencies!
Note: The chassis requires assembly but has detailed instructions.
Note: We’ve released a new kit to replace the Magician, it is called the Shadow Chassis and it can be found here.
Dimensions: 110 x 174mm
Features:
  • Max Motor Voltage: 6VDC
  • No Load Speed: 90±10rpm
  • No Load Current:190mA(max.250mA)
  • Torque: 800gf.cm
  • Stall Current: ~1A
  • 65mm Diameter Wheels (30mm Wide)
  • Plastic Rims with Solid Rubber Tires
  • Dual Output Shafts
  • Wheel Encoder Slotted Discs Included


For More Details Visit Our Website

Now Buy Online
Shipping All Across Pakistan
COMPANY: MATRIX ELECTRONICS
CONTACT PERSON:
FAIZAN MUNIR
Mobile:03002785860
Email:sales@matrixelectronic.com
Email:info@matrixelectronic.com
Address: Shop#2, Hassan Centre Near Passport Office Saddar karachi